Concrete Repair Products

Melbourne, Victoria, Australia

We are a dependable Concrete Repair Products (CRP Mortar) Manufacturer, Exporter, and Supplier. Our crp Stayput hb ohv is a balanced blend of sand, cement and active chemical components, along with synthetic reinforcing fibers to create a chemical resistant rendering. With high strength patching mortar, this product is suitable for high build structures. It bonds strongly to concrete and steel substrates. It can be applied overhead or vertical from 5mm to 40mm without falling off. The product is easy to use and quite economical, and can be colored. Uses

• Excellent for bridge repair
• Concrete cancer blow out
• Marine construction and mining
• Water proofing

Additional Information

• Payment Terms : T/T
• Minimum Order Quatity : 1000 Kilogram
• Packaging Details : Packaging is in 20 kilogram plastic pails with sealed lids. on a shipping pallet containing 50 by 20 kilogram units. Products labelled CRP STAYPUT HB OHV 20 kilogram.
• Delivery Time : 28 days from T/T receipt

We are a renowned Manufacturer, Exporter and Supplier of Concrete Repair Products (CRP AC) in Australia offering Curing Membrane, Acrylic Modified Emulsion, Concrete Surface Sealer. The Concrete Repair Product (CRP AC) is water based acrylic modified emulsion used as a curing membrane on freshly poured concrete. The Concrete Repair Product (CRP AC) meets AS3799 requirements and exhibits excellent durability as a concrete sealer. Benefits

• Dries to a clear finish
• Complies with Australian Standard AS3799
• Achieves water retention of 90% or greater
• Totally water based
• Single pack
• Reduces plastic shrinkage
• Environmentally friendly
• Can be applied by spray, roller or brush
• Will not yellow in sunlight
• Eliminates the need for curing by ponded water, damp hessian or polythene sheeting
• Seals concrete surfaces
• Takes most after trades
• Equipment washable in water

Uses : CRP AC is suitable for curing all freshly laid concrete either smooth or textured, indoors or outdoors. Typical Properties and Application Data

• Appearance : Milky white emulsion
• Coverage : 5m2 per litre
• Viscosity : 20 - 22 seconds (Ford #4)
• Solids : 40% +/- 1%
• Solubility in Water : Totally soluble
• Flash Point : Not applicable
• Solvents : Not applicable
• Shelf Life : 12 months maximum
• Dry Time : Tack Free: 1 - 3 hours
• Hard Dry : 4 - 8 hours
• Trafficable : 24 hours
• Application Temperature : 10^oC - 35^oC
• Application By : Spray - Brush

Roller - Broom

• Packaging : - 205 Lt drum

20 Lt container

• UN Number : Not applicable
• Hazchem Code : Not applicable
• Packaging Group : Not applicable
• Poison Schedule : Not applicable
• Dangerous Goods Class : Not applicable

Surface Application Apply CRP AC to the concrete as soon as the bleed water has gone and the concrete has hardened sufficiently so as not to be marked by the application process. Apply CRP AC undiluted at a rate of 1 litre per 5m². Best applied by spray, however, may also be applied by brush, roller or broom. If after trades need to be applied it is recommended that a period of 28 days from the date of pouring has elapsed before any after trades are applied. Available In : 20 ltr/ 200 Ltr/ 1000 Ltr.

The company is engaged in Manufacturing, Exporting and Supplying of Concrete Repair Products (CRP CBRP) and Prime Coat Emulsion. Due to its totally unique formulation and blend of bitumen resins and hydrocarbons, CRP BRP is an excellent cold applied primer coat, for asphalt and bitumen overlays. It is ideally suitable for bridge decks and road construction where a concrete curing compound has been removed and bitumen primer is required before the application of bitumen/asphalt wearing slab. The Concrete Repair Product (CRP BRP) is personnel safe as is applied cold -black top overlay in 6 hours. Benefits

• Ideal primer coat for asphalt or bitumen overlays on concrete roads, bridges or parking decks
• Totally water based with no solvent odor
• Can be applied to smooth or textured finish including broom finish
• Aids in the curing of concrete

Typical Properties and Application Data

• Appearance : Black Homogenous
• Coverage : 5m² per litre
• Viscosity : 0.22 Pascal seconds
• Solids : 50 +/- 1%
• Solubility in Water : Soluble
• Flash Point : 84^oC
• Solvents : Not applicable
• Shelf Life : 12 months maximum
• Dry Time : Tack Free : 1 - 3 hours
• Hard Dry : 4 - 8 hours
• Trafficable : 24 hours
• Application Temperature : 10^oC - 35^oC
• Application By : - Spray - Brush

Roller - Broom

• Packaging : 205Lt Eponlined drum

20 Lt Plastic Cube

• UN Number : Not applicable
• Hazchem Code : Not applicable
• Packaging Group : Not applicable
• Poison Schedule : 5
• Dangerous Goods Class : Not applicable

Surface Application

• Fresh concrete : Apply CRP BRP to the concrete as soon as the bleed water has gone and the new concrete has hardened sufficiently so as not to be marked by the application process. Apply CRP BRP undiluted at a rate of 1 litre per 4.5m². Best applied by spray, however, may also be applied by brush, roller or broom.
• Older Concrete : Apply CRP BRP to a clean surface . The surface can be dry or damp, but must not have standing water (puddles) . Surface must be free of dirt, dust , oils or substances and objects that could effect the bonding of CRP BRP.

Available In : 20 ltr/ 200 Ltr/ 1000 Ltr.

The company is a major Manufacturer, Exporter and Supplier of Concrete Repair Products (CRP C30). The Concrete Repair Product (CRP C30) is petroleum wax-based, type-1 class-A spray-able curing compound formulated to cure freshly laid concrete. The Concrete Repair Product (CRP C30) is a low medium viscosity and white pigmented emulsion of specially blended waxes. CRP C30 meets the requirements of AS3799 for moisture retention in liquid membrane curing compounds. Uses

• CPR C30 is suitable for curing freshly laid concrete either smooth or textured, for outdoor use
• CRP C30 can be used as a debonding agent when applied to the concrete sub base prior to pouring the concrete base
• It allows the two layers to expand and contract differently without producing cracking

Note : After thirty to thirty five (30-35) days the continuous film formed on the concrete surface will begin to degrade due to exposure of UV light. The rate of degradation will depend on the initial film thickness and degree of UV exposure. Surface Application

• CRP C30 can be easily sprayed with most commonly used spray equipment including bitumen emulsion sprayers. (Requires a minimum pressure o 280kPa [40 psi]).
• Apply CRP C30 to the concrete as soon as the bleed water has gone and the concrete has hardened sufficiently so as not to be marked by the application process.
• Apply CRP C30 undiluted at the rate of 1 litre per 5m². Best applied by spray, however, may also be applied by brush, roller or broom.
• CRP C30 performs best when one complete coat is applied, until a continuous uniform film as achieved.

Typical Properties and Application Data

• Appearance : Pale yellow colour or with red fugitive dye
• Coverage : 5m² per litre
• Viscosity : 0.02 Pascal seconds
• Solids : 23% +/- 1%
• Solubility in Water : Negligible
• Flash Point : 31^oC
• Solvents : 97 - 99% aromatics
• Shelf Life : 12 months maximum
• Dry Time : Tack Free : 1 - 3 hours
• Hard Dry : 4 - 8 hours
• Trafficable : 24 hours
• Application Temperature : 10^oC - 35^oC
• Application By : - Spray - Brush

Roller - Broom

• Packaging : 205 Lt Drum

20 Lt Container

• UN Number : 1263
• Hazchem Code : 3(Y)
• Packaging Group : III
• Poison Schedule : 5
• Dangerous Goods Class : 3.2

Available In : 20 ltr/ 200 Ltr/ 1000 Ltr.

We are counted amongst the leading Manufacturers, Exporters and Suppliers of Concrete Repair Products (CRP D30) and Moisture Evaporation Retarder. The Concrete Repair Product (CRP D30) is a wax-based, sprayable, type 1-D curing compound formulated to cure freshly laid concrete. The Concrete Repair Product (CRP D30) is a white pigmented low medium viscosity emulsion of specially blended waxes, in which D stands for dye added. CRP D30 is excellent for curing concrete structures where a bond breaker is required. It meets the requirements of AS3799 for moisture retention in liquid membrane curing compounds. Uses

• CPR D30 is suitable for curing freshly laid concrete either smooth or textured, for outdoor use
• CRP D30 can be used as a debonding agent when applied to the concrete sub base prior to pouring the concrete base
• CRP D30 allows the two layers to expand and contract differently without producing cracking

Note : After thirty to thirty five (30-35) days the continuous film formed on the concrete surface will begin to degrade due to exposure of UV light. The rate of degradation will depend on the initial film thickness and degree of UV exposure. Surface Application

• CRP D30 can be easily sprayed with most commonly used spray equipment including bitumen emulsion sprayers. (Requires a minimum pressure o 280kPa [40 psi]).
• Apply CRP D30 to the concrete as soon as the bleed water has gone and the concrete has hardened sufficiently so as not to be marked by the application process.
• Apply CRP D30 undiluted at the rate of 1 litre per 5m². Best applied by spray, however, may also be applied by brush, roller or broom.
• CRP D30 performs best when one complete coat is applied, until a continuous uniform film as achieved.

Typical Properties and Application Data

• Appearance : Pale yellow colour or with red fugitive dye
• Coverage : 5m2 per litre
• Viscosity : 0.02 Pascal seconds
• Solids : 23% +/- 1%
• Solubility in Water : Negligible
• Flash Point : 31^oC
• Solvents : 97 - 99% aromatics
• Shelf Life : 12 months maximum
• Dry Time : Tack Free : 1 - 3 hours
• Hard Dry : 4 - 8 hours
• Trafficable : 24 hours
• Application Temperature : 10^oC - 35^oC
• Application By : - Spray - Brush

Roller - Broom

• Packaging : - 205 Lt Drum

20 Lt Container

• UN Number : 1263
• Hazchem Code : 3(Y)
• Packaging Group : III
• Poison Schedule : 5
• Dangerous Goods Class : 3.2

Available In : 20 ltr/ 200 Ltr/ 1000 Ltr.

We are a renowned Manufacturer, Exporter and Supplier of Concrete Repair Products (CRP EC20). The Concrete Repair Product (CRP EC20) is a water-base formulation and environmental alternative to asphalt emulsions. The Concrete Repair Product (CRP EC20) is an alternative to Prime Coats, PCE (Prime Cure Emulsion), AEP (Asphalt Emulsion Prime), prime emulsions, and tack coats (EAP&T). The Concrete Repair Product (CRP EC20) comes with a membrane forming technology which allows it to cure, seal, and form a bond in stabilized bases. Unlike traditional asphalt emulsions and tack coats, Concrete Repair Product (CRP EC20) does not contain hydrocarbons or solvent agents like Benzenes, Mineral Spirits, Kerosene, or Petroleum Oils. It is applied cold therefore no heating is required which makes it environmental and personnel safe. Uses

• CRP EC20 is used on Cement Stabilized Bases, Flexible Asphalt Base as a primer of base materials
• It acts as a curing membrane for sealing stabilized based materials
• CRP EC20 is also ideal for erosion control, soil control, and surface
• stabilization

Specifications : CRPEC20 is a new technology being tested by the Texas Department of Transportation and Texas A&Ms Transportation Institute as an alternative to primes, cures, emulsions, and tack coats.Therefore, specifications are designed to meet or exceed the performance specifications of TxDOT. Item 300.2. Because CRPEC20 does not contain hydrocarbons, alternative specifications are currently being considered. Application : Depending upon the openness of the surface to be treated and under preliminary investigation, it was concluded that desirable results were found after an application rate of 0.5 1 litre per square meter. CRPEC20 should be applied with well sized and calibrated nozzles to deliver the desired shot rate. CRPEC20 will bond with the HMA as Technical Data

• Drying Time : Typically 2 Hours.However can depend on application rate temperature and humidity. Avoid traffic during this time period.
• Color& Odor : Brown Liquid, Odorless
• Boiling Point (⁰C) : 100^o
• Specific Gravity (H20 = 1) : 1.02
• Vapor Pressure : 7.535 (Gauge)
• Percent Volatile : 0
• Solubility In Water : Miscible
• Flammability : Non Flammable in both water and dry state

Precautions : Do not apply when temperatures are below 5^oC, keep from freezing. When applying, there should be no imminent threat of rain. Do not mix or dilute with other compounds that contain hydrocarbons or fluids that might contain petroleum distillates or water. This is a water base product, it does not contain hydrocarbons. Follow MSDS for health and safety instructions if applicable. Storage : Unlike traditional tack coats, prime coats and asphalt an emulsion, heating is not required at plant facilities, distribution Available In : 20 ltr/ 200 Ltr/ 1000 Ltr.

The company is a chief Manufacturer, Exporter and Supplier of Concrete Repair Products (CRP EC30). The Concrete Repair Product (CRP EC30) is an environmental alternative to Prime Coats and is designed to penetrate 12mm to 25mm into the base and sub-base of stabilized imestone, gravel and caliche bases. Traditionally known as cutback asphalts, prime coats (aka. primes), have been known to most effectively cure sub-base and base materials, while at the same time been scrutinized for its un-environmental application methods. Features

• Bond the HMA layer to the base
• Penetrates deeper than conventional emulsified asphalts, 12mm â 25mm of base
• Cures and evaporates faster than traditional cut backs
• Does not contain hydrocarbons
• Can lay HMA faster
• Does not require blotter sand to absorb excess material
• Dries in 2 to 3 hours
• Does not require heat to maintain in applicable conditions, reducing energy costs and liability issues regarding transportingheatedtrucks, orheatedtanks in location
• Dust Control
• Does not contain hydrocarbon related VOCâs
• Substantially reduced EPA concerns on air and water contamination
• Reduced environmental and human liability when applying / inhaling / handling cutbacks materials

Note : Preliminary investigations have led to positive results with all requirements for the products applications; however, further investigation is needed to create a workable platform for contractor traffic after 72 hours application. Current tests indicate a degrading performance if EC-30 is applied if contractor trafficisopened immediately after application. Technical Data

• Boiling Point (^oC) : 100^oC
• Specific Gravity ( H20 = 1) : 1.02
• Vapor Pressure : 17.535 ( Gauge)
• Percent Volatile : 0
• Solubility In Water : Miscible
• Appearance and Odor : Brown Liquid, Odourless
• Flammability : Non â Flammable in both Water Based and Dry State

Guidelines for Use and Application : Depending upon the openness of the surface to be treated and under preliminary investigation, it was concluded that desirable results were found after an application rate of 0.5 â 1 litre per square metre. Like traditional tack coats and curing membranes, the CRPâEC30â should be applied with well-calibrated distributors. Spray bar and distributor nozzles should be sized and set to deliver to the desire shot rate. Air and pavement temperatures should be sufficiently high to allow the emulsion to fully cure, and there should be no imminent threat of rain. Storage and Handling : CRPâEC30â is a water based suspension, and should not be exposed to freezing temperatures below 5^o or overheating over 50^oC. The emulsion is chemically stabilized, so care should be taken not to upset the chemicals balance with contamination by chemicals, over-exposure to air, or adverse mechanical or thermal conditions. Before being filed, tanks and trucks should be examined for possible contaminants. Tanks may be circulated top to bottom with a pump, but over-pumping is to be avoided. Recommended use and storage temperatures are given in the table. Precautions : Do Not Dilute with Additional Water. Do not apply when temperatures are Available In : 20 ltr/ 200 Ltr/ 1000 Ltr.

We are engaged in the manufacturing, exporting and supplying of Concrete Repair Products (CRP EcoCure). The Concrete Repair Product (CRP EcoCure) is a type-2 environmental liquid membrane compound manufactured for use on concrete Road and Highway Construction. The Concrete Repair Product (CRP EcoCure) is the first of its kind and a unique curing compound that does not contain Hydrocarbons like Resins and Mineral Spirits. The Concrete Repair Product (CRP EcoCure) has been proven to have better performance than the traditional Hydrocarbon based curing compounds. The Concrete Repair Product (CRP EcoCure) meets ASTMC309 requirements and is great for roads and bridges. It can be used for indoor or outdoor application, but never on colored concrete. Benefits

• Environmentally friendly
• Contains no harmful chemicals
• Achieves water retention of 90% or greater
• Increased abrasion resistance
• Eliminates the need for curing by ponded water, damp hessian or polythene sheeting
• Reduces concrete dusting and plastic shrinkage
• One coat application
• Equipment washable in water
• May have red fugitive dye added

Advantages CRPECOCURE was formulated to meet the stringent environmental requirements of the green construction methods. After 7 years of research and numerous testingprocedures Eco-Cure was shown to have the following advantages over existing curing systems.

• No solvents, hydrocarbons or resins of any type
• No wax or wax based additives
• No odour before or after application
• No staining of clothing or equipment
• No sticky residue
• No environmental problems from residue waste or spillage
• No health issues for personnel
• No adhesion problems with after trades
• No discoloration of the concrete surf

Uses : CRPECOCURE was formulated specifically for State, Federal and Municipal highway and airport paving projects but can be used anywhere that requires moisture retention of the concrete. Surface Application : Apply CRPECOCURE to the concrete as soon as the bleed water has gone and the new concrete has hardened sufficiently so as not to be marked by the application process. Apply CRPECOCURE undiluted at a rate of 1 litre per 5 m2. Best applied by spray, however, may also be applied by brush, roller or broom. If settling of product occurs mix gently prior to use. After 28 days CRPECOCURE oxidises and turns to dust. The dust residue can then be swept, washed or vacuumed off to leave a surface suitable for after trades. This dust does not have any adverse health or environmental issues. Typical Properties and Application Data

• Appearance : Milky liquid
• Coverage : 5m² per litre
• Solids : 6%
• Solubility in Water : Soluble
• Flash Point : >95^oC
• Solvents : Not applicable
• Shelf Life : 12 months maximum
• Dry Time : Tack Free : 20 mins
• Hard Dry : 1 hour
• Application Temperature : 10^oC - 35^oC
• Application By : - Spray - Brush

Roller - Broom

• Packaging : - 205Lt Eponlined drum

20 Lt Plastic Cube

• 1000lt Palletcon
• UN Number : Not applicable
• Hazchem Code : Not applicable
• Packaging Group : Not applicable
• Poison Schedule : Not applicable
• Dangerous Goods Class : Not applicable

Available In : 20 ltr/ 200 Ltr/ 1000 Ltr.

We are a credible Manufacturer, Exporter and Supplier of Concrete Repair Products (CRP X40). The Concrete Repair Product (CRP X40) is a blend of resins and surfactants emulsified in water and are specially formulated to cure freshly laid concrete indoors and outdoors. The impervious film formed by CRP X40 prevents excessive water evaporation, promotes efficient cement hydration and minimizes shrinkage whilst increasing durability of the concrete surface. Benefits

• Complies with Australian Standards AS3799
• Achieves water retention of 90% or greater
• Increased abrasion resistance
• Contains no wax
• Eliminates the need for curing by ponded water, damp hessian or polythene sheeting
• Reduces concrete dusting
• Reduces plastic shrinkage
• One coat application
• Can be removed, if required, by ConClena (stripper / degreaser)
• Equipment washable in water
• May have red fugitive dye added

Uses : CRP X40 is suitable for curing all freshly laid concrete either smooth or textured, indoors or outdoors. Special Features : Due to its unique formulation and blend of resins, CRP X40 will begin to break down after 7 days and, if applied at the specified application rates, will totally oxidise and leave the surface, subject to UV exposure, within 45 - 55 days of the application. Surface Application : Apply CRP X40 to the concrete as soon as the bleed water has gone and the new concrete has hardened sufficiently so as not to be marked by the application process. Apply CRP X40 undiluted at a rate of 1 litre per 5 m2. Best applied by spray, however, may also be applied by brush, roller or broom. Typical Properties and Application Data

• Appearance : Milky homogenous liquid or with red fugitive dye
• Coverage : 5m2 per litre
• Viscosity : 0.22 Pascal seconds
• Solids : 49% +/- 1%
• Solubility in Water : Soluble
• Flash Point : 84^oC
• Solvents : Not applicable
• Shelf Life : 12 months maximum
• Dry Time : Tack Free : 1 - 3 hours
• Hard Dry : 4 - 8 hours
• Trafficable : 24 hours
• Application Temperature : 10^oC - 35^oC
• Application By : Spray - Brush

Roller - Broom

• Packaging : 205Lt Eponlined drum

20 Lt Plastic Cube

• UN Number : Not applicable
• Hazchem Code : Not applicable
• Packaging Group : Not applicable
• Poison Schedule : 5
• Dangerous Goods Class : Not applicable

Available In : 20 ltr/ 200 Ltr/ 1000 Ltr.